Fire Barrier II Material Safety Data Sheet

Fire Barrier II
MULTI-FUNCTIONAL FIRE RETARDANT POLYMERS
FIRE BARRIER H SYNTHETIC
WOVEN & NON-WOVEN NATURAL & SYNTHETIC BASED TEXTILE & FABRICS FIRE RETARDANT

The Fire Barrier n SYNTHETIC fire retardant series is a clear, halogen free, non-toxic, highly concentrated water-based finish that provides excellent fire resistance properties with no after-glow when applied to combustible materials. In most cases tensile strength is increased and corrosion tests reveal stainless steel is not affected. The Fire Barrier n SYNTHETIC is specifically designed to give maximum fire resistant protection to natural and synthetic based woven & non-woven textiles and fabrics constructed of wool, rayon, silk, jute, linen, sisal and cotton and cellulose origin fibers, polyesters, acrylics, rayon's, nylons and the constructed blends of the above. They offer many advantages of treatment. Fast transparent drying with/without heat on all surfaces. No VOC's.

The SYNTHETIC series is applied by spray or any immersion/soak type processes. Clean up is with warm soap and water. The SYNTHETIC will not stain nor alter the feel or look of the treated material. The SYNTHETIC series has been independently tested to meet and exceed lie following flammability standards: NFPA 701, MVSS 302, FAA 25, Cal Tech 116 & 117, and the British Standards. All application clean up is with warm soap and water.

TYPICAL PROPERTIES
Appearance: water clear
Solubility: it is readily soluble in water
pH: >7.5
Specific Gravity: 1.13-1.18 g/ml
Density: 9,0 Ib/Gal
Odor: Slight Odor
Storage: Should be stored in area where temperature is
between 32 and 120° F, At this temperature, shelf life is at least one year
Halogen: Free
Formaldehyde: Free
Coverage: 175-225 sq. ft / Gallon

To avoid quality degradation, all Fire Barrier n polymers must be stored above 35°F and it is helpful to keep your finishing products at room temperature to avoid application errors.

Fire Barrier II
MULTI-FUNCTIONAL FIRE RETARDANT POLYMERS
FIRE BARRIER H SYNTHETIC
APPLICATION
ALWAYS TEST A SAMPLE BEFORE BEGINNING.
Application of the SYNTHETIC involves applying it in a water-solution to the fabric or fibers in a concentration that will enable sufficient SYNTHETIC to remain attached after drying to impart maximum fire resistance. SYNTHETIC may be spray applied, roll padded, or any immersion process. The amount of SYNTHETIC required firing retard any particular fabric or fiber will have to be determined for each material and for the particular fire test criteria to be satisfied. Preliminary testing must be done on all fabrics and fibers. One of the key steps is to determine the amount of SYNTHETIC pickup for the application process being used.

For example, if the goal is to add 12% SYNTHETIC to the fabric and a process allows the fabric to pickup 100% of its weight in SYNTHETIC solution, and then the solution concentration needs to be 12%. If the fabric picks up SYNTHETIC solution equal to 75% of its weight, then the SYNTHETIC solution concentration needs to be 16%. A more likely scenario for the typical textile pad treatment system is that the pickup by the fabric will be equal to 50% of its weight in which case the SYNTHETIC concentration will have to be 24% so as to leave 12% SYNTHETIC on the fabric after drying. If forced air-drying is going to be used recommended drying temperatures are between 250°F to 350°F.
When treating materials if hardness, stiffness or chalking (white deposits) are witnessed, a too high concentration of the fire retardant has been used. Dilute in 2% increments with water and re-test your sample materials until your material are properly treated and meet the specific flammability test your are trying to achieve.

This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. All statements, technical information and recommendations contained herein are based upon available scientific tests or data, which we believe to be reliable. The accuracy and completeness of such data are not warranted or guaranteed. We cannot anticipate all conditions under which this information and our products, or me products of other manufacturers in combination with our products, may be used. Since we do not have control over the exact use of our products or other factors that may affect your specific application, our providing you this data does not relieve you of the responsibility of carrying out your own tests and experiments prior to use. Therefore, we make NO WARRANTY, EITHER OF MERCHANTABILITY OR OTHERWISE ABOUT THE FITNESS OF OUR PRODUCTS FOR A PARTICULAR APPLICATION. United community of America and its subsidiaries assumes no liability or responsibility for loss or damage resulting from the improper use and handling of our products, from incompatible product combinations, or from the failure to follow instructions, warning and advisories in the product labels and Material Safety

Data Sheet.
United Community Services of America 45 Carey Ave., Butler, NJ 07405 973-492-2600
MATERIAL SAFETY DATA SHEET AND SAFE HANDLING AND DISPOSAL INFORMATION
PRODUCT NAME:
Fire Barrier H X-10
MATERIAL SAFETY DATA SHEET
This information is furnished for the purpose of compliance with OSHA Hazard Communication Standard 29 CFR 1910.1200 and Toxic Substances Control Act, 15 U.S.C and section 25 of the Canada Environmental Protection Act. SECTION I
Rating: 0=Least SECTION-II
Health 1 Fire 0 Reactivity 0
l=Slight 2=Moderate 3=High 4=Extreme
Water
Polyammoamidophosphate complex adduct (blend)
Poiyphosphate Ester complex adduct (blend) N/A
CAS NO.
7732-18-5
N/A
<20 <60
<20
TWA
N/A N/E
N/E
STEL
N/A 15mg/m3
N/A

CERCIA(COMPREHENSrVE RESPONSE, COMPENSATION, AND LIABILITY ACT) RQ: 100 Ibs All intentional ingredients are listed on the TSCA Inventory Unlisted ingredients do not appear on Massachusetts Substance List None of the ingredients are listed as carcinogens by IRAC, NTP & OSHA
SECTION HI - Physical Data
Boiling Point (F):> 212 Percent Volatile by Vol. (%): N/A Vapor Pressure (mm Hg.): N/A Evaporation Rate: N/A
Specific gravity: 1.22-1.40g/ml
pH:<5.0-7.0
Solubility in water: Soluble
Appearance: Slightly hazy to clear
SECTION IV- FIRE AND EXPLOSION
Flash Point (Method Used): N/A
Extinguishing Method: Water, CO2 Dry Chemical: N/A Lei: N/A
Special Firefighting Procedures: Wear SCBA
Unusual Explosion Hazards: Under extreme fire may release fumes of carbon oxide, carbon dioxide,
Nitrogen and Phosphorus.
SECTION V- HEALTH HAZARD DATA
Special Note: MSDS data pertains to the product as dispensed from the container. Adverse health effects would
not be expected under recommended conditions of use(diluted) so long as prescribed safety precautions are
practiced

ACCUTE EFFECTS OF OVEREXPOSURE:
This product in concentrated form may be an eye irritant. Inflammation of eye tissue is characterized by
redness, watering, and/or itching.

CHRONIC EFFECTS OF OVEREXPOSURE:
There are no known effects from chronic exposure to this product
ROUTE OF EXPOSURE: X SKIN CONTACT X INHALATION X INGESTION THRESHOLD LIMIT VALUE: See Section II
EFFECT OF OVEREXPOSURE: May cause skin irritation upon prolonged contact. Eye contact may cause irritation. Inhalation of mist may irritate respiratory tract.

EMERGENCY & FIRST AID PROCEDURES:
3KJN: Flush contaminated skin with plenty of water. Consult physician if irritation develops.

EYES: Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting upper and lower
eye lids. Get medical attention at once.

INGEST: If this product is swallowed, do not induce vomiting. If individual is alert, give plenty of water to drink. Get medical attention at once.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: N/D SECTION VI-REACTIVITY DATA

Stability- Unstable:__ Conditions to Avoid: None Known
Stable: X Incompatibility (Materials to Avoid): N/A
HAZARDOUS POLYMERIZATION: Will not occur HAZARDOUS DECOMPOSTION PRODUCTS:

See Section IV
SECTION V SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Return to container. Absorb residual with suitable material to complete clean up.

WASTE DISPOSAL METHOD: Disposal must be made in accordance with governmental regulations. To the best knowledge, this product is not regulated by CERCLA/RCRA as a hazardous material. However, this product may be disposed of as an industrial waste in a manner acceptable to good waste management practice and in compliance with applicable local, state and federal regulations. Consult local, state, and federal agencies for proper disposal method in your area. Keep containers closed when not in use.

SPECIAL PROTECTION PRECAUTIONS
PROTECTIVE CLOTHING: No special measures are required.
EYE PROTECTION: Use of tight-fitting safety glasses or goggles is strongly recommended, especially when
wearing contact lenses.

RESPIRATORY PROTECTION: Apply and use with adequate ventilation, if there is no adequate ventilation, wear OSHA approved latex spray mask.

SECTION IX- TRANSPORTATION AND SPECIAL INFO
DOT PROPER SHIPPING NAME: TDG, NON-REGULATED
DOT HAZARD CLASS: N/A
DOT ID. NUMBER: N/A DOT LABEL/PLACARD: N/A
EPA TSCA CHEMICAL INVENTORY- ALL INGREDIENTS ARE LISTED
EPA CWA 40CFR PART 117 SUBSTANCE (RQ IN SINGLE CONTAINER) NONE
This product is not regulated; MO/TMDG (Not restricted) Freight Classification: 55
ICAO/IATA: Not Restricted
ALKALINE PRODUCT: N/A Neutral PRODUCT: 2% water slurry = > 5.9 minimum

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Product is stable at 45 to 95 degrees (F) and less than a year at 120 degrees (F). Do not take internally; Do not get in eyes or on skin or on clothing. Keep out of the reach of children. Keep container closed.

Harmful if swallowed. Open all containers slowly to vent. Handle with rubber gloves, safety goggles. Avoid breathing mist or vapor. Use with adequate ventilation.

INFORMATION FURNISHED BY: United Community Services of America Date: (2/02)
This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. All statements, technical information and recommendations contained herein are based upon available scientific tests or data which we believe to be reliable. The accuracy and completeness of such data are not warranted or guaranteed. We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. United Community Services of America assumes no liability or responsibility for loss or damage resulting from the improper use and handling of our products, from incompatible product combinations, or from the failure to follow instructions, warning and advisories in the product labels and Material Safety

Data Sheet.
additional Health/Safety Information call your technical representative.
United Community Services of America
45 CareyAve., Butler, NJ 07405 973-492-2600
MATERIAL SAFETY DATA SHEET AND SAFE HANDLING AND DISPOSAL INFORMATION
PRODUCT NAME; Fire Barrier H X-20
MATERIAL SAFETY DATA SHEET
This information is furnished for the purpose of compliance with OSHA Hazard Communication Standard 29 CFR 1910.1200 and Toxic Substances Control Act, 15 U.S.C and section 25 of the Canada Environmental Protection Act. SECTION I
Health 1 Fire 0_ Reactivity 0
Rating: 0=Least l=Slight 2=Moderate 3=High 4=Extreme SECTION-H
CASNO. % TWA STEL
Water 7732-18-5 <45 N/A N/A
Polyaminophosphate N/A <45 N/E N/E complex adduct (blend)
Polyamidpolyphosphate complex N/A <10 N/E N/A adduct (blend)
CERCIA(COMPREHENSrVE RESPONSE, COMPENSATION, AND LIABILITY ACT) RQ: 100 Ibs All intentional ingredients are listed on the TSCA Inventory Unlisted ingredients do not appear on Massachusetts Substance List None of the ingredients are listed as carcinogens by IRAC, NTP & OSHA
SECTION-m- PHYSICAL DATA
Boiling Point (F):> 212 Specific gravity: 1.30 -1.35g/ml
Percent Volatile by Vol. (%): N/A pH:<6.5-7.0
Vapor Pressure (mm Hg.): N/A Solubility in water: Soluble
Evaporation Rate: N/A Appearance: Slightly hazy to clear

SECTION IV- FIRE AND EXPLOSION
Flash Point (Method Used): N/A
Extinguishing Method: Water, CO2 Dry Chemical: N/A Lei: N/A Special Firefighting Procedures: Wear SCBA
Unusual Explosion Hazards: Under extreme fire may release fumes of carbon oxide, carbon dioxide, Nitrogen and Phosphorus.

SECTION V- HEALTH HAZARD DATA
Special Note: MSDS data pertains to the product as dispensed from the container. Adverse health effects would not be expected under recommended conditions of use (diluted) so long as prescribed safety precautions are
practiced.

ACCUTE EFFECTS OF OVEREXPOSURE:
This product in concentrated form may be an eye irritant Inflammation of eye tissue is characterized by redness, watering, and/or itching.

CHRONIC EFFECTS OF OVEREXPOSURE:
There are no known effects from chronic exposure to this product
ROUTE OF EXPOSURE: X SKINCONTACT X INHALATION J^_ INGESTION JC_ THESHOLD LIMIT VALUE: See Section H

EFFECT OF OVEREXPOSURE: May cause skin irritation upon prolonged contact. Eye contact may
Cause irritation. Inhalation of mist may irritate respiratory tract.

EMERGENCY & FIRST AID PROCEDURES:
SKIN: Flush contaminated skin with plenty of water. Consult physician if irritation develops.
EYES: Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting upper and lower
eye lids. Get medical attention at once.
INGEST: If this product is swallowed, do not induce vomiting. If individual is alert, give plenty of water to
drink. Get medical attention at once.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: N/D SECTION VI-REACTIVITY DATA
Stability- Unstable:__ Conditions to Avoid: Strong Acids/Bases
Stable: X Incompatibility (Materials to Avoid): N/A
HAZARDOUS POLYMERIZATION: Will not occur HAZARDOUS DECOMPOSTION PRODUCTS: See Section IV
SECTION Vm- SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Return to container. Absorb residual with suitable material to complete clean up.
WASTE DISPOSAL METHOD: Disposal must be made in accordance with governmental regulations. To the best knowledge, this product is not regulated by CERCLA/RCRA as a hazardous material. However, this product may be disposed of as an industrial waste in a manner acceptable to good waste management practice and in compliance with applicable local, state and federal regulations. Consult local, state, and federal agencies for proper disposal method in your area. Ceep containers closed when not in use.
SPECIAL PROTECTION PRECAUTIONS
PROTECTIVE CLOTHING: No special measures are required.
EYE PROTECTION: Use of tight-fitting safety glasses or goggles is strongly recommended, especially when
wearing contact lenses.
RESPIRATORY PROTECTION: Apply and use with adequate ventilation, if there is no adequate ventilation,
wear OSHA approved latex spray mask..
SECTION IX- TRANSPORTATION AND SPECIAL INFO
DOT PROPER SHIPPING NAME: TDG, NON-REGULATED
DOT HAZARD CLASS: N/A
DOT ID. NUMBER: N/A DOT LABEL/PLACARD: N/A
EPA TSCA CHEMICAL INVENTORY- ALL INGREDIENTS ARE LISTED
EPA CWA 40CFR PART 117 SUBSTANCE (RQ IN SINGLE CONTAINER) NONE
This product is not regulated; IMO/IMDG (Not restricted) Freight Classification: 55
ICAO/IATA: Not Restricted
ALKALINE PRODUCT: N/A Neutral PRODUCT: 2% water slurry = > 6.0 minimum
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Product is stable at 45 to 95 degrees (F) and less than a year at 120 degrees (F). Do not take internally; Do not
get in eyes or on skin or on clothing. Keep out of the reach of children. Keep container closed.
Harmful if swallowed. Open all containers slowly to vent. Handle with rubber gloves, safety goggles. Avoid
breathing mist or vapor. Use with adequate ventilation.
INFORMATION FURNISHED BY: United Community Services of America Date: (2/02)
This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. All statements, technical information and recommendations contained herein are based upon available scientific tests or data which we believe to be reliable. The accuracy and completeness of such data are not warranted or guaranteed. We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. United Community Services of America assumes no liability or responsibility for loss or damage resulting from the improper use and handling of our products, from incompatible product combinations, or from the failure to follow instructions, warning and advisories in the product labels and Material Safety Data Sheet.
For additional Health/Safety Information call your technical representative.
United Community Services of America 45CareyAve., Butler, NJ 07405 973-492-2600
MATERIAL SAFETY DATA SHEET AND SAFE HANDLING AND DISPOSAL INFORMATION
PRODUCT NAME;
Fire Barrier H X-30N
MATERIAL SAFETY DATA SHEET
This infonnation is furnished for the purpose of compliance with OSHA Hazard Communication Standard 29 CFR 1910.1200 and Toxic Substances Control Act, 15 U.S.C and section 25 of the Canada Environmental Protection Act. SECTION I
Rating: 0=Least SECTION-H
Health __!_ Fire __0_ Reactivity _0_
l=Slight 2=Moderate 3=High 4=Extreme
Water
CAS NO.
7732-18-5
°olyammoamidophosphate complex adduct (blend)
N/A
<40 <60
TWA
N/A N/E
STEL
N/A 15mg/m3
CERCIA(COMPREHENSrVE RESPONSE, COMPENSATION, AND LIABILITY ACT) RQ: 100 Ibs All intentional ingredients are listed on the TSCA Inventory Unlisted ingredients do not appear on Massachusetts Substance List None of the ingredients are listed as carcinogens by IRAC, NTP & OSHA
SECTION-m - PHYSICAL DATA
Boiling Point (F):> 212 Percent Volatile by Vol. (%): N/A Vapor Pressure (mm Hg.): N/A Evaporation Rate: N/A
Specific gravity: 1.22-1.40g/ml
pH:<6.0-7.0
Solubility in water: Soluble
Appearance: Slightly hazy to clear
SECTION IV- FIRE AND EXPLOSION
Flash Point (Method Used): N/A
Extinguishing Method: Water, CO2 Dry Chemical: N/A Lei: N/A
Special Firefighting Procedures: Wear SCBA
Jnusual Explosion Hazards: Under extreme fire may release fumes of carbon oxide, carbon dioxide,
Nitrogen and Phosphorus.
SECTION V- HEALTH HAZARD DATA
Special Note: MSDS data pertains to the product as dispensed from the container. Adverse health effects would
lot be expected under recommended conditions of use(diluted) so long as prescribed safety precautions are
practiced.
ACCUTE EFFECTS OF OVEREXPOSURE:
This product in concentrated form may be an eye irritant. Inflammation of eye tissue is characterized by
redness, watering, sind/or itching.
CHRONIC EFFECTS OF OVEREXPOSURE:
There are no known effects from chronic exposure to this product
ROUTE OF EXPOSURE: X SKTNCONTACT X INHALATION_X_ INGESTION_X__ THESHOLD LIMIT VALUE: See Section n
EFFECT OF OVEREXPOSURE: May cause skin irritation upon prolonged contact. Eye contact may
Cause irritation. Inhalation of mist may irritate respiratory tract.
EMERGENCY & FIRST AID PROCEDURES:
SKIN: Flush contaminated skin with plenty of water. Consult physician if irritation develops.
EYES: Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting upper and lower
eye lids. Get medical attention at once.
INGEST: If this product is swallowed, do not induce vomiting. If individual is alert, give plenty of water to
drink. Get medical attention at once.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: N/D SECTION VI-REACTIVTrY DATA
Stability- Unstable:__ Conditions to Avoid: None Known
Stable: JL_ Incompatibility (Materials to Avoid): N/A
HAZARDOUS POLYMERIZATION: Will not occur HAZARDOUS DECOMPOSTION PRODUCTS: See Section IV
SECTION Vm- SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Return to container. Absorb residual with suitable material to complete clean up.
WASTE DISPOSAL METHOD: Disposal must be made in accordance with governmental regulations. To the best knowledge, this product is not regulated by CERCLA/RCRA as a hazardous material. However, this product may be disposed of as an industrial waste in a manner acceptable to good waste management practice and in compliance with applicable local, state and federal regulations. Consult local, state, and federal agencies for proper disposal method in your area. Keep containers closed when not in use.
SPECIAL PROTECTION PRECAUTIONS
PROTECTIVE CLOTHING: No special measures are required.
FIRE PROTECTION: Use of tight-fitting safety glasses or goggles is strongly recommended, especially when
wearing contact lenses.
RESPIRATORY PROTECTION: Apply and use with adequate ventilation, if there is no adequate ventilation,
wear OSHA approved latex spray mask..
SECTION IX- TRANSPORTATION AND SPECIAL INFO
DOT PROPER SHIPPING NAME: TDG, NON-REGULATED
DOT HAZARD CLASS: N/A
DOT ID. NUMBER: N/A DOT LABEL/PLACARD: N/A
EPA TSCA CHEMICAL INVENTORY- ALL INGREDIENTS ARE LISTED
EPA CWA 40CFR PART 117 SUBSTANCE (RQ IN SINGLE CONTAINER) NONE
This product is not regulated; IMO/IMDG (Not restricted) Freight Classification: 55
ICAO/IATA: Not Restricted
ALKALINE PRODUCT: N/A Neutral PRODUCT: 2% water slurry = > 5.9 minimum
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Product is stable at 45 to 95 degrees (F) and less than a year at 120 degrees (F). Do not take internally; Do not
get in eyes or on skin or on clothing. Keep out of the reach of children. Keep container closed.
Harmful if swallowed. Open all containers slowly to vent. Handle with rubber gloves, safety goggles. Avoid
breathing mist or vapor. Use with adequate ventilation.
WORMATION FURNISHED BY: United Community Services of America Date: (2/02)
This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. All statements, technical information and recommendations contained herein are based upon available scientific tests or data which we believe to be reliable. The accuracy and completeness of such data are not warranted or guaranteed. We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. United Community Services of America assumes no liability or responsibility for loss or damage resulting from the improper use and handling of our products, from incompatible product combinations, or from the failure to follow instructions, warning and advisories in the product labels and Material Safety Data Sheet.
For additional Health/Safety Information call your technical representative.
lOt
United Community Services of America 45 CareyAve., Butler, NJ 07405 973-492-2600

MATERIAL SAFETY DATA SHEET AND SAFE HANDLING AND DISPOSAL INFORMATION
PRODUCT NAME:
Fire Barrier H X-30S
MATERIAL SAFETY DATA SHEET
This information is furnished for the purpose of compliance with OSHA Hazard Communication Standard 29 CFR 1910.1200 and Toxic Substances Control Act, 15 U.S.C and section 25 of the Canada Environmental Protection Act. SECTION I
Rating: O^Least
SEcnoN-n
Health 1 Fire 0_Reactivity 0
l=Slight 2=Moderate 3=High 4=Extreme
CASNO.
Water
SEPolyphosphonophosphate complex adduct (blend)
7732-18-5
N/E
<45
<55
TWA
N/A
N/E
STEL
N/A N/E
CERCIA(COMPREHENSrVE RESPONSE, COMPENSATION, AND LIABILITY ACT) RQ: 100 Ibs All intentional ingredients are listed on the TSCA Inventory Unlisted ingredients do not appear on Massachusetts Substance List None of the ingredients are listed as carcinogens by IRAC, NTP & OSHA
SECTION m - PHYSICAL DATA
Boiling Point (F):> 212 Percent Volatile by Vol. (%): N/A Vapor Pressure (mm Hg.): N/A Evaporation Rate: N/A
Specific gravity: 1.32-1.40g/ml pH: < 6.0 - 8.0 Solubility in water: Soluble Appearance: Slightly hazy to clear
SECTION IV- FIRE AND EXPLOSION
Flash Point (Method Used): N/A
Extinguishing Method: Water, CO2 Dry Chemical: N/A Lei: N/A
Special Firefighting Procedures: Wear SCBA
fiNUnusual Explosion Hazards: Under extreme fire may release fumes of carbon oxide, carbon dioxide, fi^itrogen and Phosphorus.